OCMEE Design LLC 3D Printing Manufacturing Standards v2

OCMEE Design LLC
Effective Date: March 28, 2024
Last Updated: December 22, 2025

These 3D Printing Manufacturing Standards (the “Standards”) describe default process capabilities, typical tolerances, cosmetic finish expectations, and evaluation/acceptance methods for FDM and SLA printing services provided by OCMEE Design LLC (“OCMEE”). These Standards are incorporated by reference into (a) the OCMEE Design LLC Customer Service Agreement (3D Printing) v2 (the “Printing Agreement”) and (b) the OCMEE Design LLC Terms of Use, Services Terms, and Privacy Policy v2.1 (the “Master Terms”). If there is a conflict, the applicable Order Documents and the Printing Agreement control for 3D printing orders.

 

Important: These Standards describe manufacturing characteristics. They do not provide certification or suitability for any specific end use. Unless OCMEE explicitly agrees in a signed writing with a defined compliance and inspection plan, printed parts are not intended or certified for life-safety/medical, aerospace/flight-critical, restraint/braking/steering/crash-related, or other safety-critical applications. Customer is responsible for validation.

 

1) Scope

1.1 Supported processes

OCMEE provides:

FDM (Fused Deposition Modeling)

SLA (Stereolithography)

No other additive processes are provided unless explicitly stated in a Quote.

1.2 Maximum build envelope

Up to 350 × 350 × 350 mm, subject to:

part geometry and support requirements

orientation needed to meet quality/strength goals

printer availability and material constraints

Large parts may require splitting into multiple pieces. If splitting is required, it must be approved in writing and may affect strength, cosmetics, cost, and lead time.

1.3 Materials (as offered per Quote)

FDM materials: ABS, PC, PC-ABS, PLA, PETG, PA (Nylon)
SLA resins: ABS-like, Tough, Transparent

Material availability can change. If a material is unavailable, OCMEE may propose an alternative.

2) Definitions

Approved Specifications: the exact CAD file(s) and revision(s) referenced in the Quote/order confirmation and any written requirements explicitly stated in the Quote (material, finish, tolerance plan, quantity).

Critical Features: dimensions, interfaces, sealing surfaces, press fits, threads, cosmetic faces, or any features Customer identifies as critical in writing before production.

Nonconformance: a material deviation from Approved Specifications under the tolerance plan in the Quote (or Section 6 if no tolerance plan is stated).

3) File and specification requirements

3.1 Accepted file formats

Preferred:

STEP (.stp/.step) for solid models

STL/3MF for mesh models (must be watertight)

Customer is responsible for:

correct units (mm/in), scale, and revision

ensuring the model is printable (closed surfaces, no self-intersections for mesh)

3.2 What we manufacture to

Unless the Quote states otherwise, OCMEE prints to the 3D geometry in the Approved Specifications. Notes, sketches, screenshots, or verbal instructions are not controlling unless explicitly written into the Quote.

3.3 Critical feature callouts

If a feature is Critical, Customer must identify it in writing before production. If not identified, OCMEE will apply standard orientation/support strategy and standard tolerances.

4) Orientation, supports, and process control

4.1 Orientation and support strategy

Unless Customer requests a specific orientation in writing (and OCMEE confirms it in the Quote), OCMEE selects orientation and support strategy to balance:

dimensional stability

surface finish

strength direction

print success rate

lead time and cost

4.2 Support witness marks

Supports may leave witness marks (“support scars”), nubs, or surface variation. Support removal can change local surface finish and may slightly affect dimensions at support contact points.

Support marks and minor surface artifacts are expected characteristics of additive manufacturing and are not defects unless the Quote defines a cosmetic requirement for the affected surface.

4.3 Warpage and shrinkage

Warp, shrink, and distortion can occur due to thermal and curing behavior and are influenced by:

material choice (ABS/PC/PA are higher risk than PLA/PETG)

geometry (large flat surfaces are higher risk)

orientation and support needs

If you need flatness, parallelism, or tight alignment, it must be explicitly specified and may require a manual review or post-processing.

5) Cosmetic finish standards

5.1 Default cosmetic level (no cosmetic class specified)

Unless the Quote specifies a cosmetic finish level, OCMEE provides a functional prototype finish.

FDM typical characteristics (not defects by default):

visible layer lines

seam lines

minor stringing or small blobs

slight surface texture variation

support witness marks

SLA typical characteristics (not defects by default):

support witness marks

minor surface texture variation

slight edge rounding on small features

cosmetic differences due to orientation and post-cure

5.2 Transparent resin clarification

“Transparent resin” parts are not optically clear by default. Achieving near-clarity typically requires additional finishing (sanding/polishing/clear coat), which must be explicitly quoted.

5.3 Color

Color, shade, translucency, and gloss can vary across material batches and builds. Unless the Quote states otherwise, cosmetic matching to an exact color standard is not provided.

6) Dimensional tolerances (default)

Additive tolerances depend strongly on geometry, orientation, wall thickness, supports, and post-processing. Unless the Quote provides a specific tolerance plan, the following defaults apply:

6.1 Default tolerance bands (typical targets, not guarantees)

FDM: ±0.50 mm or ±0.5% of nominal dimension (whichever is greater)

SLA: ±0.20 mm or ±0.2% of nominal dimension (whichever is greater)

6.2 Features with higher variability

The following commonly deviate more and should be treated as higher risk unless specified otherwise:

holes and internal channels

long thin walls and tall slender features

large flat surfaces (flatness/warp risk)

thin snap tabs, clips, and living hinges

mating features requiring press-fit or seal contact

6.3 Holes, threads, and inserts

Holes may print undersized or out-of-round, especially on FDM.

Threads are not guaranteed unless explicitly specified.

For functional threads, OCMEE recommends:

heat-set inserts (FDM)

tapping/drilling as a post-process (FDM/SLA), quoted separately

7) Mechanical behavior and suitability

7.1 Anisotropy (FDM)

FDM parts are directionally dependent. Strength varies with layer orientation. OCMEE may orient parts to improve print success and surface finish unless orientation is specified.

7.2 Resin behavior (SLA)

SLA resins can be more brittle than thermoplastics, and properties vary by resin type and post-cure.

7.3 Suitability and validation

Customer is responsible for validating parts for:

fit and assembly

structural strength and fatigue

thermal exposure, UV exposure, chemical exposure

water tightness and sealing

compliance with any regulations or standards

OCMEE does not certify end-use performance unless explicitly agreed in writing.

8) Post-processing

8.1 Default included

Unless the Quote states otherwise:

support removal (as reasonably achievable)

basic cleanup

8.2 Optional post-processing (quoted separately)

Examples:

sanding, bead blasting

painting or coating

drilling, tapping, reaming

inserts

bonding/assembly

polishing (including transparent resin finishing)

Post-processing can affect dimensions and surface finish.

9) Inspection level (default)

Unless the Quote includes a defined inspection plan, OCMEE performs:

visual inspection for obvious print failures

basic spot-check measurements on accessible features

Formal inspection reports, full dimensional inspection, CMM, or certification/traceability must be explicitly quoted.

10) Nonconformance criteria and remedies

10.1 What counts as nonconforming

A part is considered nonconforming only if it materially fails to meet:

the Approved Specifications, and

the tolerance plan in the Quote (or the defaults in Section 6 if no plan is stated).

10.2 What is not a defect (unless quoted otherwise)

Not defects by default:

layer lines, support marks, minor surface artifacts

minor warp within tolerance bands

minor color variation

small cosmetic imperfections that do not prevent fit/function per Approved Specifications

10.3 Remedy path

If a part is nonconforming and Customer submits a valid claim under the Printing Agreement within the applicable inspection window, OCMEE will, at OCMEE’s option, reprint/replace the affected part(s) or refund/credit the amount paid for the affected part(s), as stated in the Printing Agreement. This remedy is Customer’s exclusive remedy for nonconformance.

11) Customer-provided materials and special requests

If Customer supplies material, hardware, or special instructions, OCMEE may accept or reject them at its discretion. Customer-supplied items may affect lead time, quality, and warranty coverage.

12) Updates to these standards

OCMEE may update these Manufacturing Standards from time to time. The version effective on the order date applies unless OCMEE and Customer agree otherwise in writing.

13) Contact

Questions about these standards: office@ocmeed.com